Gain Staging

Getting the right levels in your mix is the very first part of the recording process. Paying attention to your input levels can pay dividends when it comes to the mixing process. Proper levels will yield a much more streamlined workflow when it comes to sitting down to mix.

So you maybe asking yourself, “What are the proper levels that I should be trying to achieve?“

The answer to this question can vary. You have to have a vision for the end result. If you don’t have that vision, then you should focus on getting levels that optimize your A/D converters. Most interfaces are calibrated for a sweet spot around -20dBFS to -16dBFS. Hitting this area as your target RMS level will almost always give you ideal tracks to mix.

Now if you’re sitting there scratching your head and not quite sure what all that means, don’t worry. Here’s a good rule of thumb to follow. Most meters in DAWs have a color coded display. Typically green is at the bottom followed by yellow, orange, and red. If you get your average level to hover right around where the green and yellow meet, then you’re in the ballpark. This means the middle point between your peak levels and your noise floor is close to that point where the meter changes colors.

Now of course it depends on what you’re recording. Different types of sound sources are going to give you different levels. Drums are going to have very sharp attacks that will yield higher peaks. Where as a vocal that isn’t too dynamic may just hover in the same area with little movement. One of the biggest problems that I see other engineers make is the level of their monitoring. Having your monitors up too loud or down to quiet will not truly give you a representation of the signal level. This is why you have to trust the meters and your DAW and let them show you what is actually happening with you levels. These are just pretty lights for you to look at while you’re working on your tracks. These are useful tools that can mean the difference between a good or bad mix.

It’s always a good idea to leave yourself some headroom when you’re tracking. You will want to have some space to mix and that is virtually impossible when your input levels hit -3dBFS or higher. Just be reasonable when you set your levels and keep in mind that you will be blending multiple tracks to mix down to your final print track.

Today's FAQ : What's a DI?

DI is short for 'direct input' and it means you take a direct signal from a source. Usually a DI will be used for recording guitar, bass, and keyboards.

"Why should I use a DI, when I have a perfectly good amp that can be mic'd?"

Good question. If you like to mic up your amp, go ahead and do it. As a secondary back up, I'd suggest splitting the signal and tracking a DI along with your amp. You'll get a nice clean track along with your amp track to work with when you mix. Think of it as a safety net in case the amp track doesn't work out. Maybe the mic didn't capture the tone you wanted, but the performance was epic. If you tracked a DI, then the performance has a chance to be relived & re-amped!

Re-amp your performance with the DI track. You can now play back the clean DI track and feed the signal into your amp. Move the mic around until you find the tone you desire. Now you have lots of options with minimal effort and you look like a seasoned pro. There are other options like using the DI track with amp emulated software. This way you can shape your tone with digital ease. There are so many possibilities with digital software that you can try out many different sounds to hear what works best for your mix. There are so many options at the fingertips of engineers, this is a great time in musical history. Take advantage of the DI and begin to explore what your music can become.

Today's FAQ : What's a DI?

DI is short for 'direct input' and it means you take a direct signal from a source. Usually a DI will be used for recording guitar, bass, and keyboards.

"Why should I use a DI, when I have a perfectly good amp that can be mic'd?"

Good question. If you like to mic up your amp, go ahead and do it. As a secondary back up, I'd suggest splitting the signal and tracking a DI along with your amp. You'll get a nice clean track along with your amp track to work with when you mix. Think of it as a safety net in case the amp track doesn't work out. Maybe the mic didn't capture the tone you wanted, but the performance was epic. If you tracked a DI, then the performance has a chance to be relived & re-amped!

Re-amp your performance with the DI track. You can now play back the clean DI track and feed the signal into your amp. Move the mic around until you find the tone you desire. Now you have lots of options with minimal effort and you look like a seasoned pro. There are other options like using the DI track with amp emulated software. This way you can shape your tone with digital ease. There are so many possibilities with digital software that you can try out many different sounds to hear what works best for your mix. There are so many options at the fingertips of engineers, this is a great time in musical history. Take advantage of the DI and begin to explore what your music can become.

I use a Countryman 85S for most of my DI tracking. It does provide clean and clear tracks without coloration. I'd recommend it to anyone looking for a solid DI. It is my go-to DI for nearly every direct recoding done at the studio.

Most preamps can be used as a DI. I have a GML 2032 that I regularly use as a DI for bass guitar. The built-in EQ works wonders on shaping the bass sound so that it fits beautifully within the mix. Typically all I have to do is add a little compression and the bass finds a pocket in the mix.

I also have a BBE DI-1000 w/ a Jensen transformer that works amazingly well on acoustic guitars. The BBE Sonic Maximizer allows me to add just the right amount of brightness to the DI track. That way I don't have to spend hardly any time EQing the track.

I'd love to hear more from everyone. Please share what DI boxes you use for tracking.